Maintenance of the TPE surface
Introduction
For the TPE simulation skin of the doll, the material is non-toxic and is without any chemical smell.
When the TPE products are laid for a long time, there will be oil leakage on her surface which is due to the oil which is contained in the silicone formula and is a normal phenomenon. You can just wipe this away. You only need to wipe the surface gently with a non-shedding towel.
Moreover, while dolls are being used or laid aside, dust and stains can adhere to their surface. In order to keep the good performance of the silicone skin and the cleanness of the TPE surface, please carry out maintenance regularly.
The maintenance intervals differ according to the service status and storage environment.
TPE Maintenance methods
First dip the sponge or towel into warm water and then use it to wipe the doll’s surface gently. If there is dirt or smears sticking to the silicone surface, please wipe it gently many times with soap water and don’t daub it forcibly.
When one is wiping the skin surface, please don’t use corrosive cleanser such as strong acid and alkali solution, powerful disinfection solution and detergent, etc.
Soap, liquid laundry detergent, liquid shampoo, shower gel, or mild detergent are ideal to be used for cleansing.
After the surface is dry put talcum powder on the doll using a powder brush.
Maintenance of the joint parts
If the doll’s joints are kept bent for a long time, creases and wrinkles will appear on its skin surface which is due to the improper posture it is placed in and prolonged pressure on the surface.
For example, if it is placed sitting in the chair for a long time, there will be horizontal lines on its abdomen.
TPE has resilience, so when the doll is not used, keep it in the posture just like when it was delivered to you. It will reduce the stress on all joints. If the surface does wrinkle, lay the doll down for few days. The creases and wrinkles will decrease and disappear.
Maintenance of the TPE doll’s coating
The makeup done on the doll when she leaves the factory is an applied coating which usually will not rub off.
Please do not wipe it forcibly, especially the make-up on the doll’s face and the eyebrow and eyelash parts. Please pay attention to the wiping force when the doll is cleaned.
If too much force is used, the hair will rub off and its colour will also be rubbed off. Once the colour is rubbed off, it is difficult to make repairs.
Normal cosmetics can be used to apply makeup on the doll, such as lipstick and blusher, etc. Do not use anything too thick and sticky to do coating on the face or it will be difficult to do cleaning. We do not recommend the use of lip-gloss.
When changing the makeup of the doll, please don’t daub it forcibly. You should use soapy water or makeup remover to wipe it gently.
TPE Sex Doll storage environment
Introduction
To protect your companion dolls and make sure they can be used for a long time, there are certain requirements for the storage space.
A good doll storage environment can prevent the ageing of her skin, internal parts, and extend her life greatly.
Very important
The doll must have baby powder or talcum powder put on the skin; that will protect the skin from oil and dust.
After being playing with her please put her back in her original factory position. This posture is best for storage to protect her beautiful silicone skin. An alternative is to hang the doll using a specialist stand and hook system.
1. Prevent long-time exposure to the sun
Direct sun bathing should be avoided because the silicone’s colour will fade slightly after the long-term sun exposure.
2. Prevent dust sticking
Dust should be avoided because there is stickiness and static electricity on the silicone’s surface which makes it easy for the dust to stick to the surface.
When the doll is placed, please make all effort to prevent the dust from falling on it to avoid the inconvenience of extra cleaning.
3. Avoid dampness
Moist environments should be avoided because the inside of the doll is filled with sponge which will absorb water in a wet environment.
It is fine to wipe or bathe the doll with water, but soaking the doll in water for a long time will cause permanent damage.
Please do not pour water into the section of the neck where there is metal. This will cause permanent damage.
The doll’s inside is stuffed with sponge. Once water gets inside, it is hard for the doll to dry out.
4. Prevent surface staining
Please don’t put the doll on any artificial leather or dyed leather surfaces for long, for the color of the oil-soluble pigment contained in these kinds of objects may transfer and seep into the silicone permanently.
After the silicone is put on this kind of objects for more than 2 hours, serious colour changing will appear and the colour that will seep inside it is very difficult to be eradicated.
5. Pay attention to the storage temperature
Too high or too low beyond room temperature both should be avoided.
Silicone cannot be put in too low or too high an environment for a long time. Please keep the storage environment temperature between 5-35 degrees C / 40-95 degrees F.
In winter, an electric blanket can be used to warm the doll, but be sure that its temperature is not too high.
6. Prevent the doll from being squeezed
Please avoid compressing your sex doll when she is stored away. Long-term compression will distort the silicone and sponge.
Please don’t put heavy objects on the doll. Please avoid squeezing or tightening any parts of the doll for a long time.
7. Keep the doll in a posture free from external force
When placed, the doll should be kept in an unfolded posture. Being bent or squeezed for a long time will result in cracks and folds forming in the silicone.
8. This is not a toy
Please don’t place the doll in places that children can access her. This product is not children’s toy. Please prevent children from coming into contact with her.
Dressing your TPE Sex Doll
Introduction
The limbs of the TPE doll can move, but there is a certain limit to the scope of movement. When dressing the model, to protect its skin, attention should be given to the following points:
1.Use bath powder, talc or baby powder for preventing stickiness
The silicone surface can be rather sticky. One should brush bath powder or talcum powder on it before dressing the doll.
2.Prevent the limbs from bending too much
When dressing the doll, please don’t twist its arms too high which may cause TPE ruptures. Please follow the safe angle instructions. Do not put the arms directly up in the air, this causes tears under the armpits.
3.Uninstall the head before putting on a coat
When putting on a coat or parts of the clothes, if the clothes are too tight or it is inconvenient to dress the doll, it is necessary that one should remove the doll’s head before dressing it.
4.Apply powder on the doll before putting on tight pants
TPE has a lot of friction. If it is too tight to dress the doll with trousers or socks, please smear bath powder or talcum powder on the legs and try again.
5.Be careful of scratches
Please don’t make the doll wear clothing or accessories with sharp edges which may cut the silicone. If the clothing has ornaments such as sharp buttons or chains, etc., be careful.
6.Ear-piercing or navel piercing
When making the doll wear earrings and other accessories, you can use thin wire or a needle to prick holes in the silicon, but the diameter of the holes cannot be beyond 0.5mm and knives and other sharp objects cannot be used to cut. After earrings are put on, they cannot be pulled and torn otherwise you may cause TPE ruptures.
7.Fitness of the clothing
Please don’t dress the doll with too tight clothing and long-term squeezing will cause deformation or ruptures of the silicone. If the clothing is too small, please don’t try forcibly.
8.Prevent colour transfer
Some clothes are made of dyed artificial leather or other oil-stained leather materials whose colour may seep into the inside of the TPE after contact and the colour of the doll’s skin will change.
Please don’t dress the doll with these kind of clothes in order to prevent colouring damage.
TPE Sex Doll Movement Range
Do not move the dolls limbs outside of the manufacturers recommended guidelines for range.
